Steps Necessary To Pass The NACE-CIP1-001 Exam from Training Expert Free4Torrent
Valid Way To Pass CIP Level 1's NACE-CIP1-001 Exam
NACE-CIP1-001 Certification Exam is a globally recognized certification that is designed to evaluate the proficiency of individuals in the field of coating inspection. Coating Inspector Level 1 certification exam is conducted by NACE International, which is a professional organization that provides corrosion control and surface protection solutions to various industries. NACE-CIP1-001 exam tests the knowledge, skills, and expertise of individuals in the coating inspection field.
NEW QUESTION # 38
The form of corrosion that has the largest potential for unexpected catastrophic failure is:
- A. Atmospheric Corrosion
- B. General Corrosion
- C. Galvanic Corrosion
- D. Localized Corrosion
Answer: C
NEW QUESTION # 39
An inspectors personal log book should contain:
- A. Subjective comments re ding the application team
- B. Objective comments regarding the application work
- C. The inspector's personal opinions of the application team
- D. No comments regarding the application team
Answer: D
NEW QUESTION # 40
If the project specification DOES NOT state the specific DFT measurement standards, the inspector should use
- A. a detailed checklist and document the lack of a standard.
- B. their best judgment based on similar projects and specifications.
- C. NACE 2/SSPC SP10
- D. a recognized industry standard like SSPC-PA 2 that is broadly accepted
Answer: D
NEW QUESTION # 41
The NACE Inspector should perform tests for soluble salts:
- A. After surface preparation
- B. Prior to coating application
- C. Prior to surface preparation
- D. When specified
Answer: D
NEW QUESTION # 42
If a Thermoset coating is heated it will:
- A. Harden and return to its original hardness when cooled
- B. Soften when heated and retain its softness when cooled
- C. Soften when heated and return to its original hardness when cooled
- D. Harden and retain its hardness when cooled
Answer: D
NEW QUESTION # 43
The initial steel condition is important to the NACE Inspector because:
- A. It affects the final appearance after blasting
- B. If the steel is pitted more coating will be required
- C. The Inspector may have to reject the Steel
- D. Less abrasive is need if the mill Scale s gone
Answer: C
NEW QUESTION # 44
Conventional spray is a good choice when:
- A. High transfer efficiency is required
- B. High production rates are required
- C. High quality finishes are required
- D. High viscosity coatings are being applied
Answer: C
NEW QUESTION # 45
Which of these tests uses a syringe?
- A. Soluble salts meter
- B. Sleeve test
- C. Potassium ferricyanide
- D. Bresle patch
Answer: D
NEW QUESTION # 46
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Document the problem and advise the Contractor and Owner's representative
- B. Document the problem and advise the Contractor
- C. Break the blisters to see what's inside
- D. Extract any liquid that may be inside the blister and send it to the lab for further analysis
Answer: A
NEW QUESTION # 47
The main responsibilities of the inspector are to
- A. observe and report the quality of the work performed.
- B. observe and direct the work of the contractors.
- C. demonstrate to the contractor how to apply the coating.
- D. direct and perform the work stated in the specification.
Answer: A
NEW QUESTION # 48
NACE No. 4/SSPC-SP-7 is a joint standard for
- A. commercial blast cleaning.
- B. white metal blast cleaning.
- C. near-white metal blast cleaning.
- D. brush-off blast cleaning.
Answer: D
NEW QUESTION # 49
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a
- A. dry film thickness (DEI) measurement.
- B. vial lest.
- C. blotter test for the presence of oil and water.
- D. wet film thickness (WFT) measurement.
Answer: C
NEW QUESTION # 50
Polymerization is the process of:
- A. All thermoplastic coatings
- B. Monomers joining together
- C. All organic coatings
- D. Monomers telegraphing
Answer: B
NEW QUESTION # 51
When applying Thermal Spray Coatings the specification is most likely to refence:
- A. SSPC-CS 23.00/AWS C2.23/NACE No. 12
- B. NACE SP 0178
- C. SSPC PA 2
- D. NACE SP 0188
Answer: A
NEW QUESTION # 52
Stripe coats are best applied by:
- A. Brush
- B. High volume low pressure spray
- C. Airless spray
- D. Conventional spray
Answer: A
NEW QUESTION # 53
The Inspector's Log Book is generally:
- A. Retained by the inspector upon project completion
- B. Submitted to the client upon project completion
- C. Shared with all parties upon project completion
- D. Shredded by the inspector upon project completion
Answer: A
NEW QUESTION # 54
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 75 Gauge Readings resulting in 25 Spot Measurements
- B. 45 Gauge readings resulting in 15 Spot Measurements
- C. 225 Gauge Readings resulting in 75 Spot Measurements
- D. 105 Gauge Readings resulting in 35 Spot Measurements
Answer: C
NEW QUESTION # 55
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
- B. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
- C. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
- D. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
Answer: A
NEW QUESTION # 56
Removal of surface contaminants is done by:
- A. A combination of methods
- B. Waterjetting
- C. Scarifying
- D. Abrasive blasting
Answer: A
NEW QUESTION # 57
In the event of a conflict between the project specification and the coating manufactures' product data sheet, the Inspector's first course of action should be too:
- A. Call the coating manufacturer for clarification
- B. Call the person who wrote the specification for clarification
- C. Use the job specification as a guide
- D. Use the product data sheet as a guide
Answer: C
NEW QUESTION # 58
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply
- A. Rotating the dial too fast when taking measurements
- B. Failing to determine the base metal reading (BMR)
- C. Taking measurements too far from the edge of a surface
- D. Measuring ditty, tacky, or soft films
Answer: A,B,D
NEW QUESTION # 59
ISO SA 3 is directly equivalent to:
- A. NACE No. 3/SSPC SP 6
- B. NACE No. 2/SSPC SP 10
- C. None of the above
- D. NACE No. 1/SSPC SP 5
Answer: C
NEW QUESTION # 60
NACE Level 1 Inspectors have been trained to perform:
- A. All types of inspection
- B. Visual inspection only
- C. Visual inspection, Non-Destructive and Destructive testing
- D. Visual inspection and Non-destructive testing
Answer: D
NEW QUESTION # 61
Check abrasive blast pressure close to the
- A. blast pot
- B. blast nozzle
- C. substrate
- D. compressor
Answer: B
NEW QUESTION # 62
The most important factor resulting in improved job site safety is:
- A. Safety Enforcement
- B. Situational Awareness
- C. Engineering Controls
- D. Personal Protective Equipment
Answer: B
NEW QUESTION # 63
......
NACE-CIP1-001 Coating Inspector Level 1 Certification Exam is a globally recognized certification that validates the knowledge and skills of individuals in the field of coating inspection. Coating Inspector Level 1 certification exam provides individuals with a competitive edge in the job market and opens up opportunities for career growth. Coating Inspector Level 1 certification is highly valued by employers in the coating inspection industry, and it enhances the credibility and reputation of individuals in the industry.
All NACE-CIP1-001 Dumps and Coating Inspector Level 1 Training Courses: https://www.free4torrent.com/NACE-CIP1-001-braindumps-torrent.html
Free Test Engine For Coating Inspector Level 1 Certification Exams: https://drive.google.com/open?id=10_7nJY0TAye4QE3ybuwnyr36LXuCy4nq