[UPDATED 2025] Free Fortinet FCP_FGT_AD-7.6 Exam Questions Self-Assess Preparation
FCP_FGT_AD-7.6 Free Sample Questions to Practice One Year Update
Fortinet FCP_FGT_AD-7.6 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
| Topic 5 |
|
NEW QUESTION # 21
Refer to the exhibits.
An administrator wants to add HQ-ISFW-2 in the Security Fabric. HQ-ISFW-2 is in the same subnet as HQ-ISFW. After configuring the Security Fabric settings on HQ-ISFW-2, the status stays Pending.
What can be the two possible reasons? (Choose two.)
- A. SAML Single Sign-On must be set to Manual.
- B. Upstream FortiGate IP must be set to 10.0.11.254.
- C. HQ-ISFW-2 must be authorized on HQ-ISFW.
- D. Management IP must be set to 10.0.13.254.
Answer: B,C
Explanation:
The Upstream FortiGate IP should match the IP address of the Fabric Root interface, which is 10.0.11.254, not 10.0.13.254.
The new device (HQ-ISFW-2) must be authorized on the Fabric Root (HQ-ISFW) before it can join the Security Fabric, otherwise the status remains pending.
NEW QUESTION # 22
You have configured an application control profile, set peer-to-peer traffic to Block under the Categories tab, and applied it to the firewall policy. However, your peer-to-peer traffic on known ports is passing through the FortiGate without being blocked.
What FortiGate settings should you check to resolve this issue?
- A. Application and Filter Overrides
- B. Network Protocol Enforcement
- C. FortiGuard category ratings
- D. Replacement Messages for UDP-based Applications
Answer: B
Explanation:
Network Protocol Enforcement settings control how FortiGate inspects and enforces protocols on traffic, including peer-to-peer applications on known ports. If not properly enabled, peer-to-peer traffic may bypass blocking despite the application control profile.
NEW QUESTION # 23
You have configured the below commands on a FortiGate.
What would be the impact of this configuration on FortiGate?
- A. FortiGate will enable strict RPF on ail its interfaces and port1 will be enable for asymmetric routing.
- B. FortiGate will enable strict RPF on all its interfaces and port1 will be exempted from RPF checks.
- C. Port1 will be enabled with flexible RPF, and all other interfaces will be enabled for strict RPF
- D. The global configuration will take precedence and FortiGate will enable strict RPF on all interfaces.
Answer: B
Explanation:
The global setting enables strict source checking (RPF) on all interfaces by default. The per-interface setting disables the source check on port1, exempting it from strict RPF enforcement.
NEW QUESTION # 24
Refer to the exhibits.
Based on the current HA status, an administrator updates the override and priority parameters on HQ-NGFW-1 and HQ-NGFW-2 as shown in the exhibit.
What would be the expected outcome in the HA cluster?
- A. The HA cluster will become out of sync because the override setting must match on all HA members.
- B. HQ-NGFW-1 will remain the primary because HQ-NGFW-2 has lower priority.
- C. HQ-NGFW-2 will take over as the primary because it has the override enable setting and higher priority than HQ-NGFW-1.
- D. HQ-NGFW-1 will synchronize the override disable setting with HQ-NGFW-2.
Answer: C
Explanation:
With override enabled on HQ-NGFW-2 and its higher priority (110 vs. 90), HQ-NGFW-2 will become the primary device, preempting HQ-NGFW-1 despite the current primary status.
NEW QUESTION # 25
You are analyzing connectivity problems caused by intermediate devices blocking traffic in SSL VPN environment.
In which two ways can you effectively resolve the problem? (Choose two.)
- A. You should use IPsec to solve issues with fragment drops and large certificate exchanges.
- B. You can use SSL VPN tunnel mode to prevent problems with blocked ESP and UDP ports (500 or 4500).
- C. You can turn off IKE fragmentation to fix large certificate negotiation problems.
- D. You can configure a hub-and-spoke topology with SSL VPN tunnels to bypass blocked UDP ports.
Answer: B,C
Explanation:
Disabling IKE fragmentation helps resolve issues caused by intermediate devices blocking large fragmented packets during certificate negotiation.
Using SSL VPN tunnel mode encapsulates traffic over HTTPS, bypassing blocks on ESP and UDP ports commonly used by IPsec.
NEW QUESTION # 26
Which two statements about equal-cost multi-path (ECMP) configuration on FortiGate are true? (Choose two.)
- A. If SD-WAN is disabled, you can configure the parameter v4-ecmp-mode to volume-based.
- B. If SD-WAN is disabled, you configure the load balancing algorithm in config system settings.
- C. If SD-WAN is enabled, you control the load balancing algorithm with the parameter load-balance-mode.
- D. If SD-WAN is enabled, you can configure routes with unequal distance and priority values to be part of ECMP.
Answer: A,C
Explanation:
When SD-WAN is disabled, FortiGate supports volume-based ECMP mode via the v4-ecmp-mode parameter.
When SD-WAN is enabled, the load balancing algorithm is controlled by the load-balance-mode parameter within the SD-WAN configuration.
NEW QUESTION # 27
Refer to the exhibit.
A network administrator is troubleshooting an IPsec tunnel between two FortiGate devices. The administrator has determined that phase 1 status is up, but phase 2 fails to come up.
Based on the phase 2 configuration shown in the exhibit, which two configuration changes will bring phase 2 up? (Choose two.)
- A. On BR1-FGT, set Remote Address to 10.0.11.0/255.255.255.0
- B. On HQ-NGFW, enable Diffie-Hellman Group 2.
- C. On HQ-NGFW. set Encryption to AES256
- D. On BR1-FGT, set Seconds to 43200.
Answer: A,D
Explanation:
The key lifetime (Seconds) must match on both sides; BR1-FGT is set to 14400, so setting it to 43200 matches HQ-NGFW.
The remote address on BR1-FGT should match the HQ-NGFW's local subnet (10.0.11.0/24), but it is currently set incorrectly as 172.20.1.0/24. Changing it to 10.0.11.0/255.255.255.0 will align the Phase 2 selectors.
NEW QUESTION # 28
Which statement correctly describes NetAPI polling mode for the FSSO collector agent?
- A. The NetSessionEnum function is used to track user logouts.
- B. The collector agent uses a Windows API to query DCs for user logins.
- C. The collector agent must search Windows application event logs.
- D. NetAPI polling can increase bandwidth usage in large networks.
Answer: D
Explanation:
NetAPI polling mode involves frequent queries to domain controllers, which can cause increased bandwidth usage, especially in large networks with many login events.
NEW QUESTION # 29
Refer to the exhibits.
The exhibits show a diagram of a FortiGate device connected to the network, as well as the IP pool configuration and firewall policy objects.
The WAN (port2) interface has the IP address 100.65.0.101/24.
The LAN (port4) interface has the IP address 10.0.11.254/24.
Which IP address will be used to source NAT (SNAT) the traffic, if the user on HQ-PC-1 (10.0.11.50) pings the IP address of BR-FGT (100.65.1.111)
- A. 100.65.0.49
- B. 100.65.0.101
- C. 100.65.0.99
- D. 100.65.0.149
Answer: C
Explanation:
The ping traffic policy uses the IP pool named SNAT-Remote1, which has the external IP range 100.65.0.99. Therefore, traffic matching this policy (ping from HQ-PC-1 to BR1-FGT) will use 100.65.0.99 for source NAT.
NEW QUESTION # 30
Refer to the exhibits.
An administrator has observed the performance status outputs on an HA cluster for 55 seconds.
Which FortiGate is the primary?
- A. HQ-NGFW-2 with the parameter priority setting
- B. HQ-NGFW-1 with the parameter memory-failover-flip-timeout setting
- C. HQ-NGFW-1 with the parameter override setting
- D. HQ-NGFW-2 with the parameter memory-failover-threshold setting
Answer: C
Explanation:
The HA configuration shows that override is disabled (set override disable), but despite this, HQ-NGFW-1 has the higher priority (200) and is acting as the primary, as indicated by its higher resource usage and uptime. Override allows the device with higher priority to take over as primary, so HQ-NGFW-1 is the primary device.
NEW QUESTION # 31
Refer to the exhibit.
FortiGate has two separate firewall policies for Sales and Engineering to access the same web server with the same security profiles.
Which action must the administrator perform to consolidate the two policies into one?
- A. Enable Multiple Interface Policies to select port1 and port2 in the same firewall policy.
- B. Create an Aggregate interface that includes port1 and port2 to create a single firewall policy.
- C. Select port1 and port2 subnets in a single firewall policy.
- D. Replace port1 and port2 with the any interface in a single firewall policy.
Answer: A
Explanation:
Enabling Multiple Interface Policies allows you to select multiple interfaces (like port1 and port2) in a single firewall policy, consolidating access rules for both Sales and Engineering to the web server.
NEW QUESTION # 32
What are three key routing principles in SD-WAN? (Choose three.)
- A. By default. SD-WAN rules are skipped if only one route to the destination is available.
- B. By default. SD-WAN rules are skipped if the included SD-WAN members do not have a valid route to the destination.
- C. SD-WAN rules have precedence over any other type of routes.
- D. Regular policy routes have precedence over SD-WAN rules.
- E. By default. SD-WAN rules are skipped if the best route to the destination is not an SD-WAN member.
Answer: B,C,E
Explanation:
SD-WAN rules are skipped if none of the SD-WAN members have a valid route to the destination.
SD-WAN rules take precedence over other route types.
SD-WAN rules are skipped if the best route to the destination is not an SD-WAN member by default.
NEW QUESTION # 33
When configuring a FortiGate in a multi-WAN setup, why would an administrator enable session preservation on an interface?
- A. To make sure all sessions without source NAT enabled always use the primary WAN link
- B. To ensure that existing SSL VPN connections remain on the same interface even if route changes occur
- C. To improve security by forcing users to authenticate again when the WAN link changes
- D. To allow the FortiGate to dynamically change interfaces for all active sessions when a WAN link fails
Answer: B
Explanation:
Session preservation keeps active sessions, such as SSL VPNs, tied to the original interface to prevent disruption when WAN routes change.
NEW QUESTION # 34
Refer to the exhibit.
As an administrator you have created an IPS profile, but it is not performing as expected. While testing you got the output as shown in the exhibit.
What could be the possible reason of the diagnose output shown in the exhibit?
- A. FortiGate entered into IPS fail open state.
- B. Administrator entered the command diagnose test application ipsmonitor 5.
- C. There is a no firewall policy configured with an IPS security profile.
- D. Administrator entered the command diagnose test application ipsmonitor 99.
Answer: C
Explanation:
The output shows the IPS engine count as 0, indicating no active IPS engines are running. This typically means no firewall policy is referencing the IPS security profile, so the IPS profile is not being applied or triggered.
NEW QUESTION # 35
Refer to the exhibits.
The exhibits show a diagram of a FortiGate device connected to the network, and the firewall configuration.
An administrator created a Deny policy with default settings to deny Webserver access for Remote-User2.
The policy should work such that Remote-User1 must be able to access the Webserver while preventing Remote-User2 from accessing the Webserver.
Which additional configuration can the administrator add to a deny firewall policy, beyond the default behavior, to block Remote-User2 from accessing the Webserver?
- A. Configure a One-to-One IP Pool object in a new policy.
- B. Disable match-vip in the Allow_access policy
- C. Set the Destination address as Deny_IP in the Allow_access policy.
- D. Set the Destination address as Webserver in the Deny policy.
Answer: D
Explanation:
To block Remote-User2's access to the Webserver, the deny policy must explicitly specify the Webserver as the destination address; otherwise, it denies traffic to all destinations, which is not the desired behavior.
NEW QUESTION # 36
......
Real exam questions are provided for Network Security tests, which can make sure you 100% pass: https://www.free4torrent.com/FCP_FGT_AD-7.6-braindumps-torrent.html
Download FCP_FGT_AD-7.6 exam with Fortinet FCP_FGT_AD-7.6 Real Exam Questions: https://drive.google.com/open?id=1WZakeLm0yiZLkBrJt-blRELVi-sAjxM-