Exam Questions and Answers for 500-920 Study Guide Questions and Answers!
Cisco Data Center Unified Computing Infrastructure Troubleshooting Certification Sample Questions and Practice Exam
NEW QUESTION 23
After performing a UCS firmware upgrade, which two UCS components will require updated drivers? (Choose two )
- A. Cisco Fabric Interconnects
- B. VIC Cards and Fiber Channel HBAs
- C. RAID Controllers
- D. Cisco UCS Manager
Answer: A,B
NEW QUESTION 24
When troubleshooting, which option is the primary uses of the SCOPE command?
- A. To access the log files that reside in a component
- B. To access the log files on the virtual machines
- C. To access the log files on the log server
- D. The SCOPE command is not helpful in this case
Answer: A
NEW QUESTION 25
Which two components are required when the integration of Cisco UCS C-series servers within a Cisco UCS Manager Direct Connect mode? (Choose two )
- A. Compatible Cisco UCS Manager version
- B. Compatible UCS 6200 or 6300 Fabric Interconnects
- C. Cisco Management Controller
- D. Compatible Cisco Nexus Fabric Extenders
- E. Compatible UCS VIC adapter installed via the server's PCIe or MLOM slot
Answer: B,E
NEW QUESTION 26
You are in the process of upgrading your UCS M3 Server to a newer UCS M4 Server. You associate the Service Profile to the new UCS Server, but it fails to boot You suspect of a failed boot hard drive. You check your RAID1 Boot LUN in UCS Manager, but see no error messages What could be causing the issue?
- A. A misconfiguration on the Service Profile Local Disk Policy
- B. A misconfiguration on the Service Profile Local Boot Policy
- C. The newer Cisco UCS M4 Server is using flash drives, not hard drives
- D. The newer Cisco UCS M4 Server is using disks of larger capacity than the previous UCS M3 Server
Answer: C
NEW QUESTION 27
Which ethernet port type is used when configuring UCS Fabric Interconnect connections to Cisco UCS C-series servers?
- A. Direct Connect Port
- B. Service Profile Port
- C. Server Port
- D. Uplink Port
Answer: D
NEW QUESTION 28
In Cisco UCS, there are several interfaces involved on the packet path from the vNIC through the adapter, IOM to finally reach Pi Which is the order of those interfaces, starting from the vNIC?
- A. HIF. SIF, VIF, UIF NIF
- B. VIF, UIF, HIF, NIF SIF
- C. HIF. NIF, UIF, VIF SIF
- D. VIF, UIF, HIF, SIR NIF
Answer: D
NEW QUESTION 29
Which statement best describes managing Cisco UCS servers using NX-OS CLI on the Fabric Interconnects?
- A. The NX-OS CLI on the Fabric Interconnects allows you to change the connectivity configuration between the servers and Fabric Interconnects
- B. The NX-OS CLI on the Fabric Interconnects allows you to manage QoS parameters on the Fabric Interconnects and an upstream LAN switch
- C. The NX-OS CLI on the Fabric Interconnects allows you to change the connectivity configuration between the Fabric Interconnects and an upstream LAN switch.
- D. The NX-OS CLI on the Fabric Interconnects allows you to view, but not change the connectivity configuration between the Fabric Interconnects and an upstream LAN switch.
Answer: C
NEW QUESTION 30
A Hard Drive (HDD) has been hot swapped in a UCS server blade, however, the UCS Manager GUI is not displaying updated metrics about the replacement drive. What action will be required to properly display updated metrics?
- A. Remove and re-insert the server blade HDD controller mezzanine card
- B. Use the CLI, since HDD metrics cannot be displayed with the UCS Manager GUI
- C. Reboot the server.
- D. Reboot the Fabric Interconnects
Answer: A
NEW QUESTION 31
When server is booting from SAN, which command verifies the PLOGI sessions with the target?
- A. FCMap
- B. Lunmap
- C. Lunlist
- D. FCIist
Answer: C
NEW QUESTION 32
If a Cisco UCS B-Series server fails to initialize, which method of access is required to troubleshoot?
- A. Use Cisco UCS Manager API to troubleshoot initialization
- B. Use direct console access to troubleshoot initialization
- C. Use KVM console to troubleshoot initialization
- D. Use Cisco UCS Manager GUI to troubleshoot initialization
Answer: C
NEW QUESTION 33
The UCS Chassis Discovery Policy has been set to four and a new chassis is connected with two links What is the resulting chassis recognition action?
- A. The chassis will be recognized and both links will be active
- B. The chassis will be recognized but only one of the links will be active.
- C. The Chassis Discovery Policy will automatically reset to two links, since it always tracks the physical connections
- D. The chassis will not be recognized
Answer: D
NEW QUESTION 34
Which two formats can be configured for Cisco's Call Home email message? (Choose two )
- A. JSON
- B. Full text
- C. CSV
- D. XML
Answer: B,D
Explanation:
Call Home Message Formats The Call Home feature offers the following message formats: * Short Text - Suitable for pagers or printed reports. * Plain Text - Full formatted message information suitable for human reading. * XML - Matching readable format using Extensible Markup Language (XML) and Adaptive Markup Language (AML) document type definitions (DTDs). The XML format enables communication with the Cisco TAC. For user-defined destination profiles, the format options are long-text, short-text, or XML. The default is XML. For the predefined Cisco TAC profile, only XML is allowed.
Reference:
http://www.audentia-gestion.fr/cisco/smart-call-home-feature-guide-1611.pdf
NEW QUESTION 35
The command show interface veth 705 is telling you that the bound interface is Ethernet 3/1/2 What is the location of the blade that has veth 705 associated to it?
- A. There is not enough information
- B. Chassis 1. Slot 2
- C. Chassis 3. Slot 2
- D. Chassis 3, Slot 1
Answer: D
NEW QUESTION 36
What is the result of enabling the Core File Exporter in UCS Manager?
- A. A core dump file will be immediately created and transmitted using HTTP protocol
- B. A core dump must be remotely activated by Cisco TAC.
- C. A core dump will immediately be generated and will be exported
- D. If a subsequent triggering event occurs, a core dump will be generated and sent by TFTP
Answer: C
NEW QUESTION 37
Which statement is true when using SPAN for Fibre Channel (FC) Traffic?
- A. FC port on Cisco UCS 6238UP can be used as a SPAN source
- B. When defining FC uplink port as the SPAN destination, system will automatically stop using that port as an uplink port
- C. Any port can be used as a SPAN destination port Even if it is defined as Eth uplink port it will be automatically converted to FC uplink port
- D. For FC SPAN sessions we do not have to specifically enable the monitoring session
Answer: A
NEW QUESTION 38
When booting up a Cisco UCS Server you want to see boot time diagnostic messages of the POST, what action is required for you to do so?
- A. Enable Quiet Boot on the Server's BIOS
- B. Disable Fast Boot on the Server's Service Profile
- C. Disable Fast Boot on the Server's BIOS
- D. Restart the Server
- E. Enable Quiet Boot on the Server's Service Profile
Answer: E
NEW QUESTION 39
......
500-920 certification dumps - Cisco Channel Partner Data Center 500-920 guides - 100% valid: https://www.free4torrent.com/500-920-braindumps-torrent.html