Latest 2021 Realistic Verified NACE-CIP2-001 Dumps - 100% Free NACE-CIP2-001 Exam Dumps
Get 2021 Updated Free NACE NACE-CIP2-001 Exam Questions & Answer
NEW QUESTION 39
Coating application to concrete substrates is:
- A. Not required as Concrete is inorganic
- B. The same as coating steel
- C. More challenging than coating steel
- D. Less challenging, than coating steel
Answer: C
NEW QUESTION 40
The standards defining surface cleanliness achieved by centrifugal blast cleaning are:
- A. Slightly different to air blast cleaning
- B. The same as air blast cleaning
- C. Different than air blast cleaning
- D. Comparable to air blast cleaning
Answer: B
NEW QUESTION 41
The Inspectors' goal at the Pre-Job Conference is to:
- A. Obtain a clear understanding of the Specification
- B. Take accurate meeting minutes for distribution
- C. Manage the meeting so it doesn't go off topic
- D. Discuss contractual requirements
Answer: A
NEW QUESTION 42
When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:
- A. A very high reading
- B. Cold flow or creep
- C. A very low reading
- D. No difference from any other coating
Answer: B
NEW QUESTION 43
When conducting inspections the Inspector should follow which standards:
- A. NACE and SSPC standards in North America
- B. Australian standards in Australia
- C. The specified standards
- D. ISO standards in Europe and Asia
Answer: C
NEW QUESTION 44
Pre-cleaning of work pieces will NOT remove
- A. mill scale.
- B. snow, ice or water.
- C. dirt.
- D. oil or grease.
Answer: A
NEW QUESTION 45
You are the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no individual gauge reading shall be below a certain value.
As this is not part of the standard you should:
- A. Enforce the additional requirement
- B. Call your supervisor
- C. Request clarification from the specifier
- D. Ignore the additional requirement
Answer: A
NEW QUESTION 46
Differences in technique for abrasive blasting concrete versus steel require the operator to:
- A. a), b) and c)
- B. Lower the blast pressure
- C. Increase the standoff distance
- D. Move the nozzle quicker
Answer: A
NEW QUESTION 47
Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?
- A. Acid etching
- B. Sacking
- C. High-pressure water washing
- D. Stoning
Answer: B
NEW QUESTION 48
The number of air turns in an enclosure can be affected by all of these EXCEPT
- A. manufacturer of the equipment.
- B. time of the year (winter/summer).
- C. type of dehumidification equipment (refrigerant or desiccant).
- D. coating type.
Answer: D
NEW QUESTION 49
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
- A. 3-Layer Polyethylene (PE)
- B. Coal Tar Enamel
- C. 2-Layer Polyethylene (PE)
- D. Fusion Bonded Epoxy
Answer: A
NEW QUESTION 50
When performing inspection in accordance with ASTM D 4138 the Inspector will use:
- A. A set of 14 pencils of varying hardness
- B. A destructive paint inspection Tooke gauge
- C. A hardness tester
- D. A mechanical adhesion tester
Answer: B
NEW QUESTION 51
When ASIN D 3363 is specified the Inspector must:
- A. Record the percentage of failure
- B. Record the two end points identified in the standard
- C. Use the correct solvent
- D. Record the highest value attained
Answer: B
NEW QUESTION 52
You should bulk store coatings containing isocyanates
- A. in a refrigerated warehouses
- B. in a well ventilated area separate from the work place.
- C. in a heated warehouse.
- D. wherever it is convenient
Answer: B
NEW QUESTION 53
Inspection and Test Plans are provided to:
- A. Outline the inspection steps, sequencing and pass/fail criteria
- B. So the contractor has a single document to reference
- C. So the Inspector doesn't have to read the entire specification
- D. To supersede the requirements of the product data sheets
Answer: A
NEW QUESTION 54
Dehumidification is defined as the removal of moisture vapor from the air to
- A. lower its temperature
- B. raise its relative humidity.
- C. lower its dew point,
- D. provide worker comfort.
Answer: C
NEW QUESTION 55
Which standards are generally established by private-sector bodies and are available for use by any person or Organization, private or government?
- A. Voluntary
- B. De facto
- C. Mandatory
- D. Consensus
Answer: A
NEW QUESTION 56
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Magnetic Gauge
- B. Eddy Current Gauge
- C. Ultra Sonic DFT Gauge
- D. Tooke Gauge
Answer: D
NEW QUESTION 57
Non-Conformance Reports are designed to:
- A. To identify items that do not meet the specification requirements
- B. Punish the Contractor for substandard work
- C. Assist the Owner in negotiating credits from the Contractor
- D. Elevate the status of the Inspector
Answer: A
NEW QUESTION 58
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:
- A. Develop your own methodology and proceed take the readings
- B. Refuse to take readings until an is in place
- C. Use a generally accepted industry standard and to take readings
- D. Call your supervisor
Answer: C
NEW QUESTION 59
......
NACE-CIP2-001 Dumps PDF and Test Engine Exam Questions: https://www.free4torrent.com/NACE-CIP2-001-braindumps-torrent.html
Get New NACE-CIP2-001 Certification – Valid Exam Dumps Questions: https://drive.google.com/open?id=1f4tdEjDTBB8IMcW_ZzRIMQX8f5b_2_ne