Pass Your NACE NACE-CIP2-001 Exam with Correct 100 Questions and Answers
Latest [Feb 29, 2024] 2024 Realistic Verified NACE-CIP2-001 Dumps
The Coating Inspector Level 2 exam covers a wide range of topics related to surface preparation, coating application, and inspection techniques. Candidates will be tested on their understanding of coating materials, application methods, and the different types of coatings used in various industries. NACE-CIP2-001 exam will also assess candidates' knowledge of industry standards and regulations related to coatings and corrosion prevention.
NEW QUESTION # 19
You are the new NACE Level 2 Inspector on a job which had been very problematic. The previous Inspector was fired duo to personality conflicts with the Contractor's supervisor. Upon arriving onsite the Contractor's supervisor advises you in no uncertain terms that you will be the next to go, unless you cooperate with him.
Your FIRST preferred course of action is to:
- A. Challenge the supervisor's authority
- B. Express a willingness to work with the site team and follow the specification
- C. Defend the previous inspector
- D. Suggest to the Owner that the supervisor should be removed from site
Answer: B
NEW QUESTION # 20
Inspection and Test plans are developed by referencing:
- A. The Specification, Application Guidelines, 'Relevant Standards and Codes
- B. The Specification, TDS, relevant Standards and Codes
- C. The Specification, Safety Manual, Relevant Standards and Codes
- D. The Specification, SDS, relevant Standards and Codes
Answer: B
NEW QUESTION # 21
NACE Standards include:
- A. Standard Practices
- B. Material Requirements
- C. a) only
- D. a) & b)
Answer: D
NEW QUESTION # 22
NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:
- A. False
- B. True
Answer: A
NEW QUESTION # 23
Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?
- A. High-pressure water washing
- B. Acid etching
- C. Stoning
- D. Sacking
Answer: D
NEW QUESTION # 24
You are the NACE Level 2 inspector reviewing the documentation from a NACE Level 1 you notice significant documentation errors.
Your FIRST preferred course of action is to:
- A. Have the Level 1 Inspector correct the errors and set up remedial training to improve the quality of documentation
- B. Correct the errors yourself and submit the reports without any further action
- C. Correct the errors yourself and advise your supervisor that the Level 1 Inspector is incompetent
- D. Correct the errors yourself and suggest the Level 1 inspector be replaced
Answer: A
NEW QUESTION # 25
Linings are used on the interior of pipelines to
- A. provide protection against soil chemicals.
- B. protect the transported product.
- C. afford limited temperature insulation.
- D. reduce magnetic polarity.
Answer: B
NEW QUESTION # 26
The Concrete Repair Institute's comparators can be used to assess:
- A. Surface cleanliness prior to coating
- B. Contamination levels prior to coating
- C. Compressive and tensile strength prior to coating
- D. Surface profile prior to coating
Answer: D
NEW QUESTION # 27
Inspectors perform tests on linings that they may not perform on exterior coatings because
- A. linings are more durable than coatings.
- B. coatings are expected to degrade over time.
- C. coatings are more durable than linings.
- D. linings protect the contents and the container.
Answer: D
NEW QUESTION # 28
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
- A. Ignore the situation
- B. Require the Applicator to remove the coating
- C. Advise the Owner and write a Non-Conformance report
- D. Stop the job
Answer: B
NEW QUESTION # 29
A reinforced coating is
- A. less resistant to movement, abrasion, and impact than a non-reinforced coating.
- B. more resistant to movement, abrasion, and impact than a non-reinforced coating.
- C. equally resistant to abrasion and impact as a non-reinforced coating.
- D. equally resistant to movement and impact as a non-reinforced coating.
Answer: B
NEW QUESTION # 30
A failure caused by applying a coating too thinly is known as
- A. cracking.
- B. pinholes.
- C. failure to cure.
- D. chalking.
Answer: B
NEW QUESTION # 31
Which is used to calibrate a pH meter?
- A. Distilled water
- B. Deionized water
- C. Standard solvent solution
- D. Standard buffer solution
Answer: D
NEW QUESTION # 32
In which type of concrete are laitance commonly encountered?
- A. Gunite
- B. Concrete block (poured with a form)
- C. Glass fiber cement
- D. Poured (wet cast)
Answer: D
NEW QUESTION # 33
From a corrosion perspective, the main difference between Ferrous and Non-Ferrous Metals is:
- A. Cost
- B. Appearance
- C. Iron content
- D. Safety
Answer: C
NEW QUESTION # 34
The Inspectors' goal at the Pre-Job Conference is to:
- A. Manage the meeting so it doesn't go off topic
- B. Obtain a clear understanding of the Specification
- C. Take accurate meeting minutes for distribution
- D. Discuss contractual requirements
Answer: B
NEW QUESTION # 35
When observing design defects the NACE Inspector should:
- A. Stop the job immediately
- B. Ignore the defect as the inspector can't change the design
- C. Document the defect and the potential problems that could result
- D. Request that the item be rebuilt with a better design for coating
Answer: C
NEW QUESTION # 36
Examples of non-ferrous metals include
Select All that Apply:
- A. iron
- B. mild steel.
- C. aluminum
- D. copper
Answer: C,D
NEW QUESTION # 37
Inspection and Test Plans are provided to:
- A. Outline the inspection steps, sequencing and pass/fail criteria
- B. So the contractor has a single document to reference
- C. To supersede the requirements of the product data sheets
- D. So the Inspector doesn't have to read the entire specification
Answer: A
NEW QUESTION # 38
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Gel stage
- B. Cure stage
- C. Wetting stage
- D. Flow stage
Answer: D
NEW QUESTION # 39
Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?
- A. Midstream
- B. Transmission
- C. Distribution
- D. Gathering
Answer: C
NEW QUESTION # 40
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. epoxies.
- B. powder coatings.
- C. urethanes.
- D. inorganic zincs.
Answer: D
NEW QUESTION # 41
Centrifugal blast cleaning requires:
- A. A large volume of air to propel the abrasive
- B. The use of single use abrasives
- C. Well maintained blast wheels
- D. Very large nozzles
Answer: C
NEW QUESTION # 42
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Eddy Current Gauge
- B. Tooke Gauge
- C. Ultra Sonic DFT Gauge
- D. Magnetic Gauge
Answer: B
NEW QUESTION # 43
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
- A. 3-Layer Polyethylene (PE)
- B. Fusion Bonded Epoxy
- C. Coal Tar Enamel
- D. 2-Layer Polyethylene (PE)
Answer: A
NEW QUESTION # 44
......
Get 2024 Updated Free NACE NACE-CIP2-001 Exam Questions and Answer: https://www.free4torrent.com/NACE-CIP2-001-braindumps-torrent.html
Pass NACE-CIP2-001 Exam Updated 100 Questions: https://drive.google.com/open?id=1Vx9YIUsS2iYVQDbl9_zUmezqNHi2977Y